ALCOLIN MIX’N FIX FASTSTEEL® is an industrial mastic epoxy bonding bond, allowing quick and permanent repairs. It combines various materials like aluminum, wood, glass, concrete, ceramics, glass fiber, and plastics. Each bond contains pre-measured active and base portions, with contrasted colors indicating a complete mixture. Its similar consistency eliminates coulures and allows for customization before bonding.
General information :
Features & Benefits
- Strong – bonds with superior strength.
- Bonds quickly – 3-minute work life, hardens in 10 minutes.
- Steel reinforced – can be drilled, sawed, sanded, screwed, filed, carved, stained or painted.
- Mixed colour – steel grey, closely matching many metals.
- Sets to a hard finish – can be drilled, sawed, sanded, carved, stained or painted once cured.
- Long work time – for intricate moulding work.
- Waterproof – suitable for underwater applications and bonds to submerged substrates.
- Water smoothable – can be smoothed and formed with a wet finger.
- Easy to use – equal 1:1 ratio.
- 100% solids – will not shrink or pull away, no solvents.
- Chemical resistant – unaffected by most cleaning soaps and other chemicals.
- Heat resistant – can withstand up to 149°C.
- Durable – Suitable for interior and exterior use, will not rust.
- Non-toxic – releases no noxious fumes on curing.
- Non-flammable – contains no solvents.
Applications
Rebuilding small engine parts, fashioning handles.
Sealing leaks, fills cracks and voids in metal, filling rust holes.
Forming nuts and bolts, repair stripped threads.
Repairs to metal tools, equipment ducts, housing and appliances, sink traps.
Auto repairs such as bonding of trim, repairing small dents, oil pans, small parts, filling rust holes, and thread locking.
Attaching fixtures, machine tags, signs, anchor bolts, screws, rods, machine housings.
Adhesion
ALCOLIN MIX ‘N FIX FASTSTEEL® bonds to steel, iron, aluminium, copper and other metals. It also bonds wood, glass, concrete, ceramics, fibreglass, and many plastics.
Limitations
Not suitable where a flexible bond is required.
Does not bond to polyethylene, polypropylene or Teflon.
Not suitable for structural applications.
Safety instructions
ALCOLIN MIX ‘N FIX FASTSTEEL® is non-toxic, however, it is advisable to wear gloves in order to avoid direct skin contact. Individuals with extra sensitive skin should maintain caution and wash hands with soap and water thoroughly after mixing the product, or wear thin plastic gloves. In the event of eye contact, rinse thoroughly and immediately with water. Seek medical assistance if irritation or discomfort persists. May be harmful if swallowed. Keep out of reach of children! Refer to our Safety Data Sheets for further toxicological information and comprehensive handling instructions.
Surface preparation
In order to achieve optimum adhesion, surfaces should be clean and free of grease and dirt.
Roughening the surface prior to cleaning with solvent helps ensure a good bond.
Some surfaces may need to be grit blasted or abraded with a disk pad.
Poor surface preparation may result in bond failure.
Directions for use
- Cut or twist off the required amount of product.
- Mix by kneading with fingers to a uniform colour. If mixing is difficult, warm ALCOLIN MIX ‘N FIX FASTSTEEL® epoxy to room temperature or slightly above.
- Apply to the surface to be repaired within 3 minutes of mixing. Force into any cracks or holes to be filled and strike off excess material, preferably with a tool wetted with clean water. When applying to a damp, wet or immersed area, work the material forcefully into the surface and apply pressure until adhesion begins to take effect.
- For best results: Use damp fingers for easier mixing and application. Remove excess material before hardening begins. For a smooth appearance of the cured compound, hand rub with water or a damp cloth prior to hardening.
- Curing: ALCOLIN MIX ‘N FIX FASTSTEEL® epoxy has a work life of approximately 3 minutes. After 10 minutes, it will harden and form a tenacious bond. After 60 minutes, ALCOLIN MIX ‘N FIX FASTSTEEL® can be drilled, sawed, sanded, screwed, filed or painted.
- Cure rate is dependent upon the temperature of the air. The lower the temperature the longer it takes to cure.
Cleaning
Fresh epoxy can be cleaned with acetone.
Cured epoxy has to be removed mechanically or heated above 149°C.
Product packaging
57g stick (single epoxy stick consisting of activator and base supplied in a reusable clear plastic tube with a plastic friction top.)
Physical data
| Colour – Prior to mixing
Colour – Upon curing |
Grey Outer / Black Inner
Steel grey |
| Density (g/cm³) | 2.2 |
| Solids (%) | 100 |
Performance data
| Work life (minutes) | 3 |
| Hardens in (minutes) | 10 |
| Final cure (minutes) | 60 |
| Shrinkage (%) – ASTM D-2566 | <1 |
| Hardness, Shore D (full cure, 1 hour)
ASTM D-2240 |
80 |
| Lap shear tensile strength, on steel – psi
Lap shear tensile strength, on steel – kg/cm2 ASTM D-695 |
900
63 |
| Compressive strength – psi
Compressive strength – kg/cm2 ASTM D-1002 |
8 000
560 |
| Upper temperature limitations (°C)
Continuous Intermittent |
121
149 |
| Electrical resistance (megohms) ASTM D257 | 30 000 |
| Dielectric strength (volts/mil)
ASTM D-149 |
300 |
| Chemical resistance to: | Hydrocarbons, halocarbons, ketones, alcohols, esters, aqueous salt solutions, dilute acids & bases, brake fluid |
| Water resistance | Waterproof |
| Shelf life (months @ 24 °C) minimum 24 Months in sealed container | |
EN 
FR